Try changing the subnet mask and gateway on the server to:
Mask=255.248.0.0 GW=35.8.2.3
This should put the server and client on the same network.
+-------------------------------------------+
| Michael Surato |
| Resource Center for Persons |
| with Disabilities |
| Michigan State University |
| 120 Bessey Hall |
| East Lansing, MI 48824 |
| Voice: (517) 353-9643 Fax: (517) 432-3191 |
+-------------------------------------------+
-----Original Message-----
From: MSU Network Administrators Group [mailto:[log in to unmask]] On
Behalf Of Kim Geiger
Sent: Thursday, September 09, 2004 3:57 PM
To: [log in to unmask]
Subject: Re: [MSUNAG] routing problem
Hey, thanks for all the quick responses!
On 9 Sep 2004 at 14:37, dpk wrote:
> A few questions to aide in debugging.
> What static route makes it work?
35.8.232.0 mask 255.255.255.0 35.8.232.1
> What does tracert output from a client show?
Nothing. It can't even make one hop to the server without timing out.
> What subnet mask and gateway do you use on the Netware server?
mask=255.255.255.0 GW=35.8.232.1
> Are the server and clients on the same physical network segment?
Uh... I don't know. They're in the same building; clients over in your
building don't have the problem (see below).
> netstat -r from both the server and clients may also be helpful.
SERVER:
Destination Gateway Flags Metric Netif Age
35. 8.232. 0 wkar.msu.edu US 1 Q57_1_EII_EII
1148844
Default com3-rtr-s232.net GUS 1 Q57_1_EII_EII
10552
CLIENT:
========================================================================
===
Active Routes:
Network Destination Netmask Gateway Interface
Metric
0.0.0.0 0.0.0.0 35.10.42.1 35.10.42.111
1
35.8.0.0 255.248.0.0 35.10.42.111 35.10.42.111
1
35.10.42.111 255.255.255.255 127.0.0.1 127.0.0.1
1
35.255.255.255 255.255.255.255 35.10.42.111 35.10.42.111
1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1
1
224.0.0.0 224.0.0.0 35.10.42.111 35.10.42.111
1
255.255.255.255 255.255.255.255 35.10.42.111 35.10.42.111
1
Default Gateway: 35.10.42.1
========================================================================
===
And On 9 Sep 2004 at 15:30, Surato, Michael wrote:
> There are a couple of things to try. First attempt to run a traceroute
> (tracert 35.8.232.2) from the client to the server. This will tell you
> where the problem is from the client end. The next thing to test is a
> trace from the server to the client (nwtrace 35.10.x.x). One of these
> traces should give the address/name of the offending router.
As I said above, client times out on the first hop. From the server to
the client, the first (and only) hop is to 35.8.188.1 (huh?
what router is that?); the rest of the hops time out.
> The other issue to check is to make sure that the default route on the
> server points to 35.8.2.3. This particular router seems to work better
> than other routers in the configuration here.
? 35.8.232.3 is not a router. Default route points to 35.8.232.1
Finally, On 9 Sep 2004 at 14:57, John Resotko wrote:
> On the Netware side of things, you will need to advertise Netware
> services on the TCP/IP protocol by configuring SLP, and designating
> one of your Netware servers as the primary SLP DA (directory agent)
server.
Thank you. I may well not have configured this properly, and will check
out the Novell TIDs you suggested. However, I'm not sure that SLP is
the problem per se, since I have some clients in another
building/network segment who can log in and do stuff on the server using
pure IP, and I didn't do anything special to make that work.
Many thanks again.
Kim Geiger
Information Technologist
MSU Broadcasting Services
538 Communication Arts & Sciences Building East Lansing, MI 48824 - 1212
517-432-9527 x 429
|
